1. Product Overview
This paint is based on a waterbone, acrylic emulsion polymer. This fast drying paint has excellent properties such as weatherability, abrasion resistance and washability. This paint is environmentally friendly one-component type paint, because of low VOC (volatile organic compounds) content.
This product is a paint that has a function that allows the driver to check in advance and prepare for the route when the driver is at the forked road.
2. Product Characteristics
- Fast drying and excellent workability.
- Excellent weatherability and abrasion resistance.
- High durability because it can be coated thick even with one time coating with high solid content.
- Non-flammable, non-toxic (no lead, chromium, mercury, cadmium, etc.) and eco-friendly.
3. Recommended use
- Line marking of asphalt and concrete road.
- Guide lane marking
4. Type (color and recommended use)
Color
Standard color (Munsell number)
Recommended use
Pink
5.0RP 8.0 / 6.0
1,2 direction forked road,
automatic payment lane
Green
5.0G 5.0 / 10.0
2 direction forked road
Light green
5.0GY 7.0 / 8.0
Rest area
Blue
8.2B 7.2 / 6.4
Hi-Pass in highway(General vehicle)
Orange
10.0R 6.0 / 12.0
Hi-Pass in highway(Freight vehicle)
※ These grades are experimental results. Quality can not be guaranteed if user does not observe the coating thickness, type of glass and the amount of application.
5. Properties
Color
Pink, Green, Light green
Recommended film thickness (㎛)
Wet film : 420 ㎛
Blue, Orange
Dry film : 260 ㎛
Viscosity (at 25℃)
80 - 90KU
Drying time (20℃)
set-to-touch : min. 10
Specific gravity
1.58 – 1.62
no-pick-up : min. 20
Solids by volume (%)
62 ±2%
Coverage (㎡/ℓ)
2.3 ㎡/ℓ
Application
Spray, roller
15 m/ℓ (thickness 15cm)
※ The application area may vary depending on the condition of the road surface and the coating method.
6. Reflective glass beads
Type
Consumption (kg/m2)
Application
SWARCOLUX50 TYP I T14
0.42 kg/m2
manual and mechanical
7. Application |
- Surface preparing : Remove the moisture, dirt, oil etc from the surface of the road. - Surface condition : To avoid condensation of moisture, the surface temperature should be more than 10 ℃ or more than 3 ℃ higher than dew point, and the relative humidity should be 70% or less. - Application : spray, roller - Thinner : non thinning - Temperature : Use at atmospheric temperature 10 ℃ ~ 40 ℃. ( ※ Application below 10 ℃ will causes poor drying and poor adhesion. ) - Vehicle pass available time : min. 20 / 20 ~ 25℃ (Recommended film thickness wet. 420㎛) |
8. Cautions on coating |
- Avoid painting when the relative humidity is above 70% and the substrate surface temperature is below 10℃. ( Occur of problem (crack, poor adhesion etc.) ) - Do not mix with other company products. - Use after confirming the compatibility with the old film on repairing the old film. - Use the total amount that has been opened products. Storage containers are then sealed and stored at a temperature 5 ℃ ~ 35 ℃ and humidity of 70% or less. - It is possible that the film is formed on the product, so please use the filter net when entering the storage tank to prevent the film from entering. - Remove the moisture, dirt, oil etc from the surface of the road. - Stir to be mixed uniformly before application. - Don′t thinning. - It is necessary to coat with the specified coating amount. In case of excessive coating at one time, the problem of drying failure may occur. - If the coating surface is new concrete, apply it when the curing time is sufficient (curing for more than 30 days at 20 ℃), the pH is 7 ~ 9 and the water content is less than 8%. - In case of repetitive painting, it should be painted after confirming that it is sufficiently dried. (Lifting, wrinkling, reverling, etc. may ocuur) - Use at atmospheric temperature 10 ℃ ~ 40 ℃. For avoid condensation of moisture, the surface temperature should be more than 10 ℃ or more than 3 ℃ higher than dew point. |
9. Cautions on handling |
- Prohibition of use other than the recommended use. - Keep out of reach of children. Do not apply to children's equipment and food storage containers. - When transporting, storing and handling the product, avoid fire and direct sunlight, store it in a dry and dark, keep the container sealed, and keep the filling port facing up. - To prevent environmental pollution, completely use the contents and dispose of the remaining amount through the designated waste disposal company. - Do not store or paint near fire. Avoid sparks due to impact, friction, etc. during handling. - In case of contact with eyes, rinse immediately with plenty of water and seek doctor. - If inhaled, move to a place with clear air. If irritation develops, consult a doctor immediately. - If ingested, seek medical advice immediately. - Use the product in efficacy period. (12 months) ※ For more information on product safety, see the Material Safety Data Sheet (GHS-MSDS). |
