대화페인트



HOME 대화페인트
DAEHWA PAINT

대화페인트

제품 목록

SAFETY-150

  • Anti Skid and Area Marking

Product Details

1. Product Overview

SAFETY-150 is the based on the reactive MMA resin, extender and pigment(black, red, green, etc). SAFETY-150 is a non-skid product which provides excellent adhesion durability and anti-abrasion. In particular, since fasten curing and reaction at low temperature, it can be applied in the winter. It makes slope, skid road to be non-skid road. After applying it provide driver or pedestrian safety on the road, school zone.

2. Product Characteristics

- Excellent film flexibility prevents cracking.

- Excellent adhesion to asphalt and concrete.

- Excellent abrasion resistance, impact resistance and excellent durability.

- Excellent weatherability.

- Fast curing time and excellent low temperature curing ability, which shortens the working time.

- Environmentally friendly product that does not contain volatile organic compounds (VOC).

3. Recommended use

- It is used for landscape and strength reinforcement by coating the surface of ascon, concrete and etc.

- School zone, crosswalk, pedestrian road, park, bicycle road, theme street, and etc.

4. Properties

Color

Reddish brown, Green,

Other required colors

Recommended amount

Paint : 2 ~ 2.5 kg/

Composition

Paint(liquid) / Hardener(powder)

 

Hardener : 0.04 ~ 0.06 kg/

Viscosity (at 25)

10 000 ~ 20 000 mPa/s

 

Silica sand : 0.2 ~ 0.3 kg/

Specific gravity

White : 1.70 - 1.80

Coverage

0.4 ~ 0.5 /kg

Solids by volume(%)

above 99%

 

11 ~ 12/pail (25kg)

Application

Spray (Requires dedicated equipment)

Drying time (20)

Pot life : 15 ~ 20 min.

 

Manual (dedicated equipment or rake)

 

Curing time : 40 ~ 60 min.

Recommended film thickness (mm)

1.5 ±0.5mm

 

Vehicle Passage available Time : 60 min.

The application area and drying time may vary depending on the condition of the road surface, the coating method and the temperature.



7. Working process

Traffic control & Surface preparing
- Safety check and passage
  control.
- Remove contaminants (oil,
  dust, etc.) on the site to
  be applied.

  
Masking tape attach
- Conduct surveying according
  to road alignment.
- Masking using tape.

 

Silica sand & hardener mix
- Mix 20 ~ 25% of silica sand
  into the paint and stir thoroughly.
- Specified amount of hardener
  into the paint, thoroughly
  mix using a hand drill.

  
Application & Finishing
- Apply uniformly to specified
  thickness using dedicated
  equipment.
- After application, finish using
  rollers and dedicated equipment.
- Products containing a
  hardener should be used
  within the pot life.

 

Masking tape remove
- Remove the masking tape
  immediately after application.

  
경화 후 교통개방
- Check the curing condition
  of the anti-skid agent and
  arrange the surroundings.
- Open traffic passage.

 

8. Cautions on coating

- Keep the mixing ratio. If the mixing ratio is different, problems such as poor curing and adhesion may occur.

- If you use mixture that is past the pot life time, adhesion failure and other problems may occur.

- In case of concrete surface, apply dedicated primer.

- Stir to be mixed uniformly before application.

- Do not mix with other company products.

- Isolate from fire because the rate of evaporation is fast.

- Avoid painting when the relative humidity is above 85% and the substrate surface temperature is below 5.

( Occur of problem (adhesion failure, poor curing, etc.) )

- Use after confirming the compatibility with the old film on repairing the old film.

- Remove the moisture, dirt, oil etc from the surface of the road.

- Non thinning. If the thinner is mixed, it causes poor curing.

- It is necessary to coat with the prescribed coating amount at the time of coating so that the coating performance can be

demonstrated.

- If the coating surface is new concrete, apply it when the curing time is sufficient (curing for more than 30 days at 20 ),

the pH is 7 ~ 9 and the water content is less than 8%.

- In case of repetitive painting, it should be painted after confirming that it is sufficiently dried.

(Lifting, wrinkling, reverling, etc. may ocuur)

- Use at atmospheric temperature 5 ~ 45 . To avoid condensation of moisture, the surface temperature should be 3

above the dew point.

(If the temperature below 5 , curing accelerators should be used.)



Product Notes

9. Cautions on handling

- Prohibition of use other than the recommended use.

- Keep out of reach of children. Do not apply to children's equipment and food storage containers.

- When transporting, storing and handling the product, avoid fire and direct sunlight, store it in a dry and dark,

keep the container sealed, and keep the filling port facing up.

- To prevent environmental pollution, completely use the contents and dispose of the remaining amount through the

designated waste disposal company.

- Contains organic solvents and may cause headaches, dizziness, and other health problems. Avoid ingestion,

inhalation of vapors, and skin contact.

- Protective gloves, masks, and protective clothing must be worn when painting, and thoroughly wash exposed skin

after painting.

- Do not store or paint near fire. Avoid sparks due to impact, friction, etc. during handling.

- In case of contact with eyes, rinse immediately with plenty of water and seek doctor.

- If inhaled, move to a place with clear air. If irritation develops, consult a doctor immediately.

- If ingested, seek medical advice immediately.

- Use the product in efficacy period. (6 months)

For more information on product safety, see the Material Safety Data Sheet (GHS-MSDS).